Skip to content
Tool A14Available

Net-zero roadmap for supply-chain SMEs

A practical net-zero roadmap from a year of your bills: the steps in order, what each saves, costs from your own quotes, and a statement for the customers who ask.

Ready to use. Buy it in your account: a one-time licence fee and a monthly fee, plus the AI it uses.

01

What it does

Type a base year of figures from your bills, as for a carbon footprint: electricity, gas or oil, fuel or miles for your vehicles, and if you like travel and purchases. Add the changes you are planning or that fit your business (a van lease ending, an old boiler, a building you lease) and any quotes you already have. We work out your base year with published emission factors, then the most each change we can measure would save: a renewable electricity tariff, a heat pump in place of fuel heating, electric vehicles, and rail instead of short flights. The AI puts the steps in order with a suggested year each, timed to your plans, and adds steps we cannot measure, such as insulation or lighting. We work out each step's saving, the path of your scope 1 and 2 emissions against the SME Climate Commitment (halve by 2030, net zero by 2050), and the cost only from your own quotes: every other step says 'Get a quote'. You also get a plan for your wider footprint, a statement for your customers and a yearly progress routine.

Who it is for

  • Manufacturers, hauliers, builders' suppliers and food producers whose larger customers ask for a net-zero plan
  • Small suppliers who have a carbon baseline and need to show what comes next
  • Owners planning a boiler, van or tariff change and wanting it to count
02

Quick start

  1. 01Gather a year of figureskWh from your electricity and gas bills, and litres of fuel or miles driven. Travel and purchases are optional.
  2. 02Add your plans and quotesFor example: Van lease ends in 2028; Air source heat pump: £16,500. Without quotes, steps say 'Get a quote'.
  3. 03Run itIt takes a minute or two. You can leave the page: the result waits in your run history.
  4. 04Check and shareCheck each step suits your premises and budget, then give the statement to your customers.
03

What you give it

Your base yearRequired, up to 80 characters
The base year your roadmap starts from, for example January to December 2025.
Energy used on your premises in that yearRequired, up to 20 lines
Energy used on your premises that year, a line each, in kWh, litres, therms or cubic metres as on your bills.
Vehicles the business owns or leasesOptional, up to 20 lines
Vehicles you own or lease: fuel bought or miles driven, a line each. Optional.
Business travelOptional, up to 20 lines
Business travel: distances flown or by rail, and hotel nights, a line each. Optional.
What you buy, by spendOptional, up to 30 lines
What you spend on things you buy, excluding VAT, a line each. Rough estimates. Optional.
US only: your electricity grid regionOptional, choose one of 28
US only: your eGRID electricity region, for a more accurate electricity figure. Optional.
Changes you are planning or that would fitOptional, up to 15 lines
Changes you are planning, dates such as a lease ending, and anything that limits you. Optional.
Quotes or prices you already haveOptional, up to 15 lines
Quotes or prices you already have, a line each with the amount. Optional.
Anything elseOptional, up to 1,500 characters
Anything else, such as when a customer needs the plan by. Optional.
04

What you get

The target and your base year
Your scopes 1 and 2 in the base year, what halving them by 2030 means for you, and whether the measured steps get there.
The steps, in order
Each step with a suggested year, what to do, what it applies to, the saving we worked out and how, and the cost from your quotes. Downloadable as a spreadsheet.
Where the steps take you
Your scope 1 and 2 emissions year by year as the steps happen. Downloadable as a spreadsheet.
Your wider footprint
What to do about purchases and travel (scope 3), without made-up savings.
Statement for your customers and progress routine
A paragraph to give your customers, and how to report progress each year.
What to check
Notes for you only: steps that miss the 2030 cut, assumptions to confirm with an installer, figures we did not work out and any net-zero claim.

You can edit the result, then copy it, print it or download it as Word, Markdown, plain text or data. Every run is kept in your run history until you delete it.

05

An example

Ridgeway Metalworks is a made-up business. Below is what was entered, then the tool's real result, unedited, made on 6 November 2026. Subscribe to run it with your own details.

What was entered

From Ridgeway Metalworks’s Business profile

What you sell
Steel brackets and fabrications made to order for builders, from a workshop in Leicester
Your base year

January to December 2025

Energy used on your premises in that year
  • Electricity: 64,000 kWh
  • Gas: 88,000 kWh
Vehicles the business owns or leases
  • Van diesel: 18,000 miles
What you buy, by spend
  • Packaging: £6,200
  • Machine servicing: £4,800
Changes you are planning or that would fit
  • The gas boiler is 15 years old and due for replacement in 2027
  • Our van lease ends in 2028
Quotes or prices you already have
  • Air source heat pump for the workshop: £16,500

3 optional details were left empty.

In your account this is a form you fill in, and the tool runs once you subscribe.

What the tool returned

Your roadmap

From 31.87 tonnes CO2e (scopes 1 and 2, 2025): the measured steps cut 85.3% by 2030

In short

In the base year 2025, Ridgeway Metalworks produced 23.49 tonnes of scope 1 and 8.38 tonnes of scope 2 emissions, 31.87 tonnes in total, against a 2030 target of 15.94 tonnes. The biggest steps are replacing the gas boiler with a heat pump when it is due in 2027 (up to 12.59 tonnes a year) and switching to a renewable electricity tariff (up to 8.38 tonnes a year). Together these two steps are enough to reach the 2030 target, and moving to an electric van when the lease ends in 2028 (up to 6.21 tonnes a year) takes the business further.

The target

  • The SME Climate Commitment: halve scopes 1 and 2 by 2030 and reach net zero by 2050. For you, 31.87 tonnes CO2e in the base year means no more than 15.94 tonnes in 2030.
  • The measured steps cut scopes 1 and 2 by 85.3% by 2030, which meets it.
  • Net zero means cutting emissions by at least 90% (the SBTi Corporate Net-Zero Standard) and removing what is left. The measured steps cut scopes 1 and 2 by 85.3% by 2050.
  • Scope 3 (your purchases and travel) has no fixed target here: the commitment asks you to measure it and reduce it, as in the scope 3 section.

Your base year

Part 1

Part: Scope 1 (fuels and owned vehicles)

Tonnes CO2e: 23.49

Share: 63%

Part 2

Part: Scope 2 (electricity, location-based)

Tonnes CO2e: 8.38

Share: 22.5%

Part 3

Part: Scope 3: purchases (spend-based estimate)

Tonnes CO2e: 5.43

Share: 14.5%

Part 4

Part: Total

Tonnes CO2e: 37.3

Share: 100%

The steps, in order

1. Switch to a renewable electricity tariff

Suggested year: 2026

What to do

Check the end date and exit terms of the current electricity contract. Ask suppliers for a tariff backed by renewable generation, ideally with certificates for the electricity supplied. Switch at the next renewal point and keep the supplier's fuel mix statement for each year's report.

Applies to: Electricity

Saving a year (tonnes CO2e): 8.38

How the saving was worked out

Market-based: electricity on a renewable tariff backed by certificates (REGOs in the UK, RECs in the US) counts as zero in market-based reporting. Your location-based figure does not change.

Cost: Get a quote

2. Tighten heating controls and timings in the workshop

Suggested year: 2026

What to do

Set the boiler timer to match working hours, lower set-point temperatures where the work allows, and keep doors closed when heating is on. Read the gas meter monthly to see the effect and to help size the replacement heating system.

Applies to: Not measured by the platform

Saving a year (tonnes CO2e): Not worked out: measure it after

How the saving was worked out: We cannot measure this change from your figures. Compare your bills or records the year after.

Cost: Get a quote

3. Reduce electricity use in the workshop

Suggested year: 2026

What to do

Walk round the workshop to find machines, compressors and lighting left on when not in use, fix any compressed air leaks, and switch equipment off at the end of each day. Consider LED lighting where existing lights are older types. Read the electricity meter monthly to track the effect.

Applies to: Not measured by the platform

Saving a year (tonnes CO2e): Not worked out: measure it after

How the saving was worked out: We cannot measure this change from your figures. Compare your bills or records the year after.

Cost: Get a quote

4. Replace the gas boiler with an air source heat pump

Suggested year: 2027

What to do

The boiler is due for replacement in 2027, so plan the heat pump for then rather than a like-for-like gas boiler. During 2026, have an installer survey the workshop's heat loss, confirm the size of unit needed and any electrical upgrades, and fix draughts first. Check that the business can make changes to the building and get any permission needed from the landlord if it rents. Compare the existing quote with at least one more and check for any grants available at the time.

Applies to: Natural gas

Saving a year (tonnes CO2e): 12.59

How the saving was worked out

Assumes your boiler turns 90% of its fuel into heat and a heat pump gives 3 units of heat for each unit of electricity over the year; the extra electricity is counted at the grid factor.

Cost: £16,500 (your quote: Air source heat pump for the workshop: £16,500)

5. Replace the diesel van with an electric van at the end of its lease

Suggested year: 2028

What to do

The van lease ends in 2028. During 2027, check that an electric van's range and payload suit typical delivery runs with steel brackets and fabrications, look into a charge point at the workshop, and ask leasing companies for electric options so the new lease can start when the old one ends. Plan delivery routes to cut unnecessary mileage in the meantime.

Applies to: Van, diesel

Saving a year (tonnes CO2e): 6.21

How the saving was worked out: The same miles in an electric van, at the DESNZ 2026 factor for charging one.

Cost: Get a quote

Where the steps take you

Year 1

Year: 2025 (base year)

Scopes 1 and 2 (tonnes CO2e): 31.87

Change from the base year: -

Year 2

Year: 2026

Scopes 1 and 2 (tonnes CO2e): 23.49

Change from the base year: -26.3%

Year 3

Year: 2027

Scopes 1 and 2 (tonnes CO2e): 10.9

Change from the base year: -65.8%

Year 4

Year: 2028

Scopes 1 and 2 (tonnes CO2e): 4.69

Change from the base year: -85.3%

Year 5

Year: 2030

Scopes 1 and 2 (tonnes CO2e): 4.69

Change from the base year: -85.3%

Year 6

Year: 2050

Scopes 1 and 2 (tonnes CO2e): 4.69

Change from the base year: -85.3%

What it costs

£16,500 from your quotes for 1 step; the other steps need quotes.

Your wider footprint (scope 3)

Area 1

Area: Paper and card packaging (SIC 17)

What to do

Ask packaging suppliers for the carbon figures of the products bought, choose recycled or lighter packaging where it still protects the parts, and ask builder customers whether reusable packaging could work for regular orders. Record quantities bought, not just spend, to measure this better.

Area 2

Area: Equipment repair and servicing (SIC 33 (other))

What to do

Ask the machine servicing provider for its own carbon figures and plans, and whether visits can be combined to cut travel. Keep machines well maintained so they run efficiently and last longer.

Statement for your customers

Ridgeway Metalworks has measured its carbon footprint for the base year January to December 2025. Our direct emissions (scope 1) were 23.49 tonnes of CO2e and the emissions from the electricity we bought (scope 2) were 8.38 tonnes of CO2e. We are committed to halving our scope 1 and 2 emissions by 2030 and reaching net zero by 2050. Our plan is to switch to a renewable electricity tariff and improve our heating controls in 2026, replace our gas boiler with a heat pump in 2027, and move to an electric van when our current lease ends in 2028. We are also working with our suppliers on the emissions from the goods and services we buy. We will report our progress against our 2025 base year each year.

Reporting progress each year

  • Read the electricity and gas meters monthly and keep the bills, so each year's use can be compared with the 2025 base year.
  • Record the van mileage each month and keep fuel or charging records.
  • Keep yearly spend and quantities for packaging and machine servicing, and any carbon figures suppliers provide.
  • Each January, enter the previous year's figures into the platform with the same method as the base year and compare scopes 1 and 2 with the 2030 target.
  • Publish a short yearly update for customers showing the figures, which steps have been completed and what is planned next.

How it was worked out

  • Base year: January to December 2025. Scopes follow the GHG Protocol Corporate Standard; scope 2 is location-based in the baseline and the trajectory, except where a renewable tariff step is counted market-based, as it says.
  • Factors: UK government (DESNZ) greenhouse gas conversion factors for company reporting 2026, version 1.2. Purchases: Defra and University of Leeds spend-based emissions multipliers, SIC multipliers 2023 (kg CO2e per £, excluding VAT), rough estimates.
  • Savings are worked out by us, not the AI, for four changes: a renewable tariff, a heat pump, electric vehicles and rail instead of flights. Each step says how. Other steps are not measured.
  • Target: the SME Climate Commitment (halve emissions by 2030, net zero by 2050), applied to scopes 1 and 2.
  • Costs come only from the quotes you typed. We never estimate a price.

Your base-year lines

Line 1

Id: L1

Line: Electricity: 64,000 kWh

Activity: Electricity

Scope: Scope 2

Tonnes CO2e: 8.38

Line 2

Id: L2

Line: Gas: 88,000 kWh

Activity: Natural gas

Scope: Scope 1

Tonnes CO2e: 16.04

Line 3

Id: L3

Line: Van diesel: 18,000 miles

Activity: Van, diesel

Scope: Scope 1

Tonnes CO2e: 7.45

Line 4

Id: L4

Line: Packaging: £6,200

Activity: Paper and card packaging (SIC 17)

Scope: Scope 3 (estimate)

Tonnes CO2e: 4.15

Line 5

Id: L5

Line: Machine servicing: £4,800

Activity: Equipment repair and servicing (SIC 33 (other))

Scope: Scope 3 (estimate)

Tonnes CO2e: 1.28

Only for you: not included when you copy, print or download

Check before sharing

  • The heat pump saving rests on an assumed boiler and heat pump efficiency: ask your installer for the figures for your building.
  • The renewable tariff saving is market-based: report your location-based electricity figure too, and keep the tariff's certificates.
  • Check every step suits your premises and budget before you share the roadmap with a customer.
06

What the AI does

It does

  • Puts the steps in order and times them to your plans
  • Adds practical steps we cannot measure
  • Writes the scope 3 plan, a statement for customers and a progress routine
  • Never states a saving, a price or a grant amount, or claims you are net zero

It does not

  • Price a step without your quote
  • Survey your building or say a heat pump will suit it
  • Certify or validate a target
  • Count refrigerants, commuting or what happens after your goods leave you

Please check itCheck each step with your installer, supplier or landlord before you commit to it, and keep the certificates for a renewable tariff.

07

Limits

  • Your base year: up to 80 characters.
  • Energy used on your premises in that year: up to 20 lines.
  • Vehicles the business owns or leases: up to 20 lines.
  • Business travel: up to 20 lines.
  • What you buy, by spend: up to 30 lines.
  • US only: your electricity grid region: choose one of 28.
  • Changes you are planning or that would fit: up to 15 lines.
  • Quotes or prices you already have: up to 15 lines.
  • Anything else: up to 1,500 characters.
  • One base year a run.
  • UK and US factor sets; other countries use the UK set, and the result says so.
  • Your workspace's monthly cap: a run that would take you over it pauses, and carries on where it stopped when you raise the cap.
08

Your data

  • What you enter, the files you choose and the result are stored encrypted with your workspace's own key. Only people in your workspace can open them.
  • To produce the result, what you give the tool (and the parts of your Business profile it uses) is sent to our AI provider, Anthropic. It uses it only to answer, and its terms do not allow it to train its models on it. We do not train on it either.
  • Files you upload are deleted after 30 days unless you choose to keep them. You can delete a run at any time: what you entered, the result and the progress notes go; only the usage record stays, because it is part of your billing.
  • Our service is hosted in the United States.

The full details are in our privacy notice.

09

Questions

How are runs charged?

A one-time licence fee of $1,200 (£1,200 in the UK), then $300 a month (£250 in the UK), including any tax that applies. On top, you pay for the AI each run uses, billed each month with your invoice and never more than the monthly cap you set. From your fourth tool there is no licence fee.

Can I change the result?

Yes. Choose Edit this result to change any wording or figure, and Restore the original result to go back. Copy, print and downloads use your edited version.

Is it ready to use now?

Yes. Sign in, open Tools in your account and choose Get started for this tool.

Who works out the savings?

We do, not the AI, for four changes: a renewable tariff, a heat pump, electric vehicles and rail instead of flights. Each step says how its saving was worked out. Other steps are listed without a saving.

Where do the costs come from?

Only from the quotes you type. We never estimate a price, so a step without a quote says 'Get a quote'.

Which target does it use?

The SME Climate Commitment: halve emissions by 2030 and reach net zero by 2050, applied to your scope 1 and 2 emissions. Net zero means cutting by at least 90% and removing the rest.

10

If something goes wrong

A line was not counted.
Start it with what it is (electricity, gas, van, flights…) and end with the amount and unit, for example: Gas: 52,000 kWh.
A step shows 'Get a quote'.
Add the quote, a line with the amount, and run it again.

Still stuck? Use the enquiry form and say which tool and what you saw.